{"product_id":"fuel-injector-clinic-1200cc-d-high-impedance-injector-set-for-ls3-ls7-lsa-l76-l92-and-l99-1","title":"Fuel Injector Clinic 1200cc-D High-Impedance Injector Set for LS3, LS7, LSA, L76, L92 and L99","description":"\u003cp\u003e\u003cstrong\u003eFuel Injector Clinic 1200cc-D High-Impedance Injector Set for LS3, LS7, LSA, L76, L92 and L99\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePart Number: IS303-1200H-D\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Fuel Injector Clinic IS303-1200H-D is a matched set of eight high-impedance fuel injectors for LS3, LS7, LSA, L76, L92, and L99 applications.\u003c\/p\u003e\n\u003cp\u003eEach injector flows approximately 1200 cc\/min at 43.5 psi and 1350 cc\/min at the GM original-equipment fuel pressure of 58 psi. The additional capacity over the 1000 cc set makes the 1200cc-D well suited to higher-output forced-induction and E85 combinations while retaining the short-pulse control and characterization needed for stable idle and part-throttle operation.\u003c\/p\u003e\n\u003cp\u003eFuel Injector Clinic individually serial-numbers and tests each injector using its Data Match Technology process. The supplied data sheet includes dynamic slope flow information, individual injector offset deviations, and voltage-offset data for accurate ECU configuration.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e• Set of eight matched port-fuel injectors\u003cbr\u003e• Designed for LS3, LS7, LSA, L76, L92, and L99 applications\u003cbr\u003e• 1200 cc\/min nominal flow rate at 43.5 psi or 3 bar\u003cbr\u003e• Approximately 110 lb\/hr at 43.5 psi\u003cbr\u003e• Approximately 1350 cc\/min at 58 psi or 4 bar\u003cbr\u003e• Approximately 130 lb\/hr at 58 psi\u003cbr\u003e• Saturated, high-impedance electrical design\u003cbr\u003e• Suitable for gasoline and E85 applications\u003cbr\u003e• Individually serial-numbered injectors\u003cbr\u003e• Matched using Fuel Injector Clinic Data Match Technology\u003cbr\u003e• Application-specific GM ECU data available from Fuel Injector Clinic\u003cbr\u003e• O-rings supplied for the listed factory application\u003cbr\u003e• Covered by Fuel Injector Clinic’s lifetime limited warranty for the original purchaser\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKit Includes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e• Eight Fuel Injector Clinic 1200cc-D high-impedance injectors\u003cbr\u003e• Application-specific upper and lower O-rings\u003cbr\u003e• Fuel Injector Clinic Data Match sheet with injector characterization information\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTechnical Specifications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFlow Rating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e• 1200 cc\/min at 43.5 psi differential fuel pressure\u003cbr\u003e• Approximately 110 lb\/hr at 43.5 psi differential fuel pressure\u003cbr\u003e• Approximately 1350 cc\/min at 58 psi differential fuel pressure\u003cbr\u003e• Approximately 130 lb\/hr at 58 psi differential fuel pressure\u003cbr\u003e• Flow tested using CF-16B calibration fluid at approximately 90°F\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eElectrical Configuration\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e• Saturated, high-impedance injector design\u003cbr\u003e• Compatible with conventional saturated injector drivers\u003cbr\u003e• No external injector resistor pack required in supported applications\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInjector Characterization\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e• Dynamic slope flow rate for each individually serial-numbered injector\u003cbr\u003e• Individual injector offset-deviation values\u003cbr\u003e• Injector voltage-offset table\u003cbr\u003e• Application-specific GM ECU data available from Fuel Injector Clinic\u003cbr\u003e• Injector data must be entered correctly for the ECU, fuel pressure, and fuel being used\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eApplication Notes\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e• This injector set is designed for LS3, LS7, LSA, L76, L92, and L99 intake, fuel-rail, and harness configurations.\u003cbr\u003e• This listing is for one matched set of eight injectors.\u003cbr\u003e• Fuel Injector Clinic supplies the O-rings required for the listed factory application.\u003cbr\u003e• Aftermarket fuel rails, intake manifolds, injector bungs, or unusual combinations may change the required injector length, O-ring size, or electrical connection.\u003cbr\u003e• Confirm fitment before ordering when using non-factory rails or intake hardware.\u003cbr\u003e• The published 1200 cc\/min rating is measured at 43.5 psi differential fuel pressure.\u003cbr\u003e• At the GM factory pressure of 58 psi, the injectors flow approximately 1350 cc\/min.\u003cbr\u003e• Injector flow changes with differential fuel pressure; ECU configuration must reflect the actual base pressure and manifold-pressure reference strategy.\u003cbr\u003e• Injector characterization data must be entered into the ECU rather than relying only on the nominal flow rating.\u003cbr\u003e• Fuel-system capacity, pump selection, regulator capacity, line sizing, filtration, and electrical supply must be adequate for the intended fuel and power level.\u003cbr\u003e• Fuel Injector Clinic identifies its high-impedance injectors as compatible with gasoline and E85.\u003cbr\u003e• Power capability is not specified because required injector capacity depends on fuel type, base pressure, brake-specific fuel consumption, duty-cycle target, and engine configuration.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eEmissions and Competition-Use Notice\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eUnless specifically identified as emissions-legal for the applicable vehicle and application, this product is intended for sanctioned competition, off-road, or other non-emissions-controlled use. Installation or use on an emissions-controlled vehicle operated on public roads may violate federal, state, or local law. The purchaser and installer are responsible for confirming and maintaining compliance with all applicable emissions and vehicle-use regulations.\u003c\/em\u003e\u003c\/p\u003e","brand":"Fuel Injector Clinic","offers":[{"title":"Default Title","offer_id":46273722417209,"sku":null,"price":1077.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0809\/8512\/9017\/files\/IS303-1200H-D_10497180-0e0a-4f98-9b01-4e854c4a3077.webp?v=1785767098","url":"https:\/\/rad-power.com\/products\/fuel-injector-clinic-1200cc-d-high-impedance-injector-set-for-ls3-ls7-lsa-l76-l92-and-l99-1","provider":"RAD","version":"1.0","type":"link"}